jh.chun
36c8958e03
- 배치 내부에서 cmake --build로 merged.hex 갱신 - chiperase + program + verify 후 nrfjprog --rbp ALL로 SWD 디버그 포트 잠금
62 lines
1.9 KiB
Batchfile
62 lines
1.9 KiB
Batchfile
@echo off
|
|
setlocal enabledelayedexpansion
|
|
|
|
REM ==============================================================
|
|
REM Build + Flash + APPROTECT lock (PRODUCTION ONLY)
|
|
REM - Rebuilds so build\merged.hex is up to date, then flashes.
|
|
REM - Do NOT run on development boards (locking needs --recover).
|
|
REM ==============================================================
|
|
|
|
set "REPO=%~dp0.."
|
|
set "BUILDDIR=%REPO%\build"
|
|
set "HEX=%BUILDDIR%\merged.hex"
|
|
|
|
REM cmake from the nRF Connect toolchain, fallback to PATH
|
|
set "CMAKE=C:\ncs\toolchains\fd21892d0f\opt\bin\cmake.exe"
|
|
if not exist "%CMAKE%" set "CMAKE=cmake"
|
|
|
|
echo [FLASH] FULL ERASE + APPROTECT LOCK mode (production)
|
|
echo [FLASH] This wipes application flash, NVS/settings, and BLE bonds.
|
|
echo [FLASH] After locking, SWD debug read/write is disabled.
|
|
echo [FLASH] To unlock later: nrfjprog --recover (mass-erases the chip).
|
|
echo [FLASH] DFU(SMP) over BLE still works after locking.
|
|
echo.
|
|
|
|
REM --- Step 1: build (updates merged.hex) ---
|
|
echo [FLASH] Step 1/4: build (update merged.hex)
|
|
"%CMAKE%" --build "%BUILDDIR%"
|
|
if errorlevel 1 (
|
|
echo [FLASH] Build FAILED. Aborting.
|
|
exit /b 1
|
|
)
|
|
|
|
if not exist "%HEX%" (
|
|
echo [FLASH] merged.hex not found: %HEX%
|
|
echo [FLASH] Build the project first.
|
|
exit /b 1
|
|
)
|
|
echo [FLASH] Using: %HEX%
|
|
echo.
|
|
|
|
REM --- Step 2: chip erase + program + verify ---
|
|
echo [FLASH] Step 2/4: chip erase + program + verify
|
|
nrfjprog --program "%HEX%" --chiperase --verify --reset
|
|
if errorlevel 1 (
|
|
echo [FLASH] Program FAILED. Aborting before lock.
|
|
exit /b 1
|
|
)
|
|
|
|
REM --- Step 3: enable APPROTECT ---
|
|
echo [FLASH] Step 3/4: enabling APPROTECT (readback protection)
|
|
nrfjprog --rbp ALL
|
|
|
|
REM --- Step 4: pin reset to apply protection ---
|
|
echo [FLASH] Step 4/4: pin reset
|
|
nrfjprog --pinreset
|
|
|
|
echo.
|
|
echo [FLASH] Done. POWER-CYCLE the device to fully latch APPROTECT.
|
|
echo [FLASH] Verify lock: nrfjprog --memrd 0x0 should now FAIL.
|
|
endlocal
|
|
pause
|